Features
Diagnostics
Unique to interVOLT, is the self diagnosing electronics. This design provides valuable feedback to installers and operators alike. Twin LED’s display the system status and will indicate standby power, lamp load connected (lights on), over temperature and output short circuit.
Protection
interVOLT dimmers feature a host of devices designed to protect the electronics from various connection and application problems. The dimmers are protected against, short circuit, over temperature and an internal fuse protects the electronics in the event of component failure.
Memory
All interVOLT dimmers have an integrated device which stores data for various functions including the memory feature. The memory function records the current ‘brightness’ setting when the lights are switched off, so that same ‘brightness’ is resumed when turned on again. The DuoDim has the added advantage of memory retention upon power loss as well – truly unique!
Soft Starting
A special feature of interVOLT dimmers is the soft start function. High inrush current diminishes the life of common filament lamps. This feature controls the start up power by limiting the in-rush current, considerably extending the bulb life.
Safety
An innovative feature of our dimmers is the temperature failsafe mode. Most electronic dimmers either fail or shutdown on temperature overload. interVOLT dimmers are programmed to dim the lighting circuit to 50% of full load if the electronics should overheat.
Dual Channel
The DuoDim is a true two channel dimmer in that each channel is capable of controlling and monitoring two separate lighting circuits. In UNGROUP mode the total power output of the DuoDim is equally divided between the two channels. In GROUP mode the two channels can be combined and controlled with one switch only thereby using the total power of the whole dimmer as one. Thus the DuoDim is truly two dimmers in one!
Specifications
|
Model No.
|
SLD2040DD
|
|
Continuous Load Rating @ 30°C (86ºF)
|
In GROUP mode 100 Watts @ 13.0VDC or 200 Watts @ 26.0VDC per channel
In UNGROUP mode 200 Watts @ 13.0VDC or 400 Watts @ 26.0VDC total overall
|
|
Length Overall
|
135mm (5.315”)
|
|
Width Overall
|
80mm (3.150”)
|
|
Height Overall
|
40mm (1.575”)
|
|
Weight
|
300 grams (10.6 oz)
|
|
InputVoltage Range
|
9 – 33VDC
|
|
Dimming Voltage Range
|
10– 98% of input voltage
|
|
Standby Current Draw
|
<10mA
|
|
Operator
|
One single pole momentary push switch (normally open) for each channel.
Multiple switches can be used within the same circuit
|
|
Operating Temperature
|
-25°C to + 45°C
|
|
Operating Humidity
|
Ideally less than 90%
|
|
Enclosure Material
|
Marine grade aluminium dye anodised
|
|
End Cap Material
|
Injection moulded electrical grade ABS/PC plastic
|
|
Terminal Cover Material
|
Extruded temperature resistant ABS
|
|
Diagnostic Indicator
|
Twin tri-colour LED – monitoring standby mode, load on, short circuit and temperature
|
|
Transient Voltage Protection
|
Filtering - Purpose designed circuit
|
|
Short Circuit Protection
|
Current sensing circuit – Shutdown (automatic reset)
|
|
Over Temperature Protection
|
Temperature sensing circuit – Foldback to 50% of rated load (automatic reset)
|
|
Input Reverse Polarity Protection
|
Internal Fuse – Diode bypass circuit (not user serviceable)
|
|
Termination
|
Power – 6-32 UNC H/D screw terminal. Auxiliary – Euro terminal block
|
|
Single/Group Selection
|
Use selectable slide switch. Located next to auxiliary terminal
|
|
Conformity
|
EMC – Australian AS2064 and European EN50081-1 / EN50082-1
|
|
Certification
|
EMC – Australian C Tick mark and European CE mark
|
FAQs
If you have questions regarding this product please fill in the following form: